How To Measure Countertops For Granite

It may look like it would be simple, but there are many variables to determine this including possible waste factor. Note that the average measurement of the backsplash is 4 inches.

Factory Plaza measure fabricate and install Quartz counter

Each sq foot has 144 sq in.

How to measure countertops for granite. Multiply this number by the width then divide by 144 to get the total square footage estimate. Square inches of bar area. Choosing granite as the surface for your countertops is an investment.

Just measure the length starting from the flat end to the farthest point on the curve or the apex. If you would like get accurate estimate for your granite countertops. Measure length from end of counter to wall or point where next section of countertop begins.

Below are step by step instructions on how to measure your existing countertops. 914.5 sq in / 144 sq in = 6.35 sq ft. Once completed, you can tear out the sheet along the perforated.

Your fabricator will ask for the measurements of your counters. If they prefer square feet, just divide that number by 12. Its important to figure out square footage.

Measure the length in the same manner. 31 in x 4 in = 124 sq in. Countertops prior to meeting with a granite surfaces sales associate.

Sketch your countertop layout, noting the approximate location of the sink, cooktop, and other cutouts. For example, say the length of the countertop is 108 and the depth of the standard countertop (on a 24 deep cabinet) is 25 ; Standard height of splash = 4 inches.

Make sure you measure to the closest 1/8 inch. Divide the figure you get by performing the steps above by 144. Divide your countertop into sections (refer to the above chart for some typical layouts) measure the length and width of each section (in inches) of your countertop.

125 x 25 = 3125. Some countertops are as easy to divide into rectangles, as we saw in the kitchen above. Measure depth, from wall or back of counter to front for each section as well.

Your regular standard kitchen base cabinet is 24 deep. You just take the length x width of each section, and add it together. You can use the graph paper on the back of this page to draw your kitchen countertop configuration and record your measurements.

1620 144 = 11.25 sq. Multiply your total length by 26, the width in inches of standard countertops, to find total countertop area in square inches. Begin with a scale drawing of your countertop layout or layouts.

However, the calculations for the area are the same. Measure the length of one section of your countertops by running a measuring tape flush along the back edge of the section from one end to the other end. An island countertop that is not against the wall will require a 1 overhang on each side or, if.

Area = length width. Take the length of section b & multiply by the depth of section b. You will need to reach the wall behind the countertop and use a tape measure, so make sure nothing.

However, handy homeowners can save money by measuring and installing the countertops themselves. This will help determine how many slabs we will need for your project. So, 44 inches times 26 inches yields 3,744 square inches.

Divide this number by 144. Take measurements of the entire length of each countertop you want covered in granite. For galley kitchens or in island situations, dont be concerned about scaling the aisle separations.

Add the total of section a & section b & round to the nearest sq. This can help you get the right granite figure the backsplash needs. 54 x 30 = 1620 sq.

The length of your 1st existing countertop is 125 and width is 25 or 125 x 25. 15.0 + 11.25 = 26.25 sq. Please note that granite countertops have a 1 standard over hang from the face of the cabinets.

Multiply the length of your of your granite countertops by 4. Make sure to measure each counter section individually and as accurately as possible. Using the box method, start at the wall and measure to the counter edge.

Same size as a in this case, so 1562.5. Always start from the wall and measure to the edge of your countertop. Clear your countertops of any appliances, vases or other items.

How to measure for appliances Dont stop measuring when you reach a sink but continue to measure until you reach the end of a cabinet, appliance, or a wall. Follow these steps to measure for countertops.

Use the tape measure to measure each section of countertop in inches. Important considerations when measuring for granite countertops. 62.5 x 25 = 1562.5.

31 in x 25.5 in = 790.5 sq in. This will give you the width. / the total counter top is 26 sq.

To calculate the area of the oddly shaped piece below, we will follow the same formula: 108 x 25.5 = 2,754 (divide this number by 144) 2,754/144 = 19.12 sq ft. * now divide by 144 to obtain square footage.

I gathered as many lightcolored and marblelook quartz